Aluminium Coil/Sheet 1000 Series
1000 series typical alloy: Aluminium Sheet 1100, 1050, 1060, Aluminium Coil 1060, 1050, 1100, 1200, 1235; etc
Temper: H12, H14, H16, H24, H18, O, H112
Size available (thickness): 0.2~4.0mm, (C. C)
4.0~6.0mm, (C. C or D. C) Over 6.0mm (D. C)
Width: Normally 700~2600mm
Description: Pure aluminum (. 99% min. ) is highly resistant to attack by chemicals and rural, industrial and marine atmospheres. Easily worked and ductile enough for deep draws. For general use in applications where the essential qualities of aluminum will be beneficial.
Surface: Mill finished with bending angle, embossed, tread available,
Tolerance: Edge trim, accord to ASTM H35 and GB/T 3880
PVC fim available
Alloy and temper designations are in accordance with ANSI H35.1.
Equivalent standard in Chinese: GB/T3190 for chemical composition and GB/T3880 for mechanism properties.
General Quality:
Unless otherwise specified, the material shall be supplied in the mill finish and shall be uniform as defined by the requirements of this specification and shall be commercially sound. Any requirement not covered is subject to negotiation between producer and purchaser.
Each sheet and plate shall be examined to determine conformance to this specification with respect to general quality and identification marking. On approval of the purchaser, however, the producer may use a system of statistical quality control for such examinations
| Alloy | Temper | Thickness in Sheets (mm) | Thickness in Coil (mm) |
| 1A97,1A93,1A90,1A85 | F | >4.50-150.00 | — |
| H112 | >4.50-80.00 | — | |
| 1235 | H12,H22 | >0.20-4.50 | >0.20-4.50 |
| H14,H24 | >0.20-3.00 | >0.20-3.00 | |
| H16,H26 | >0.20-4.00 | >0.20-400 | |
| H18 | >0.20-3.00 | >0.20-3.00 | |
| 1070 | F | >4.50-150.00 | >2.50-8.00 |
| H112 | >4.50-75.00 | — | |
| O | >0.20-50.00 | >0.20-6.00 | |
| H12,H22,H14,H24 | >0.20-6.00 | >0.20-6.00 | |
| H16,H26 | >0.20-4.00 | >0.20-4.00 | |
| H18 | >0.20-3.00 | >0.20-3.00 | |
| 1060 | F | >4.50-150.00 | >2.50-8.00 |
| H112 | >4.50-80.00 | — | |
| O | >0.20-80.00 | >0.20-6.00 | |
| H12,H22 | >0.50-6.00 | >0.50-6.00 | |
| H14,H24 | >0.20-6.00 | >0.20-6.00 | |
| H16,H26 | >0.20-4.00 | >0.20-4.00 | |
| H18 | >0.20-3.00 | >0.20-3.00 | |
| 1050,1050A | F | >4.50-150.00 | >0.20-8.00 |
| H112 | >4.50-75.00 | — | |
| O | >0.20-50.00 | >0.20-6.00 | |
| H12,H22,H14,H24 | >0.20-6.00 | >0.20-6.00 | |
| H16,H26 | >0.20-4.00 | >0.20-4.00 | |
| H18 | >0.20-3.00 | >0.20-3.00 | |
| 1145 | F | >4.50-150.00 | >2.50-8.00 |
| H112 | >4.50-25.00 | — | |
| O | >0.20-10.00 | >0.20-6.00 | |
| H12,H22,H14,H24,H16,H26,H18 | >0.20-4.50 | >0.20-4.50 | |
| 1100 | F | >4.50-150.00 | >2.50-8.00 |
| H112 | >6.00-80.00 | — | |
| O | >0.20-80.00 | >0.20-6.00 | |
| H12,H22 | >0.20-6.00 | >0.20-6.00 | |
| H14,H24,H16,H26 | >0.20-4.00 | >0.20-4.00 | |
| H18 | >0.20-3.00 | >0.20-3.00 | |
| 1200 | F | >4.50-150.00 | >2.50-8.00 |
| H112 | >6.00-80.00 | — | |
| O | >0.20-50.00 | >0.20-6.00 | |
| H111 | >0.20-50.00 | — | |
| H12,H22,H14,H24 | >0.20-6.00 | >0.20-6.00 | |
| H16,H26 | >0.20-4.00 | >0.20-4.00 | |
| H18 | >0.20-3.00 | >0.20-3.00 |
