Aluminium Coil (Non heat treatment alloy 1000, 3000, 5000 Series)
Commonly used: Aluminium coil 1100, 1050, 3003, 3105, 5005, 5052 etc
Temper: Hard (H18/H28), semi-hard(H14/H24), soft and annealed (O) etc
Size: Thickness from 0.2mm~25mm approximately
Width: 700~2500mm approximately
Surface: Mill finished with bending angle, embossed, tread available
Tolerance: Edge trim, accord to ASTM H35 and GB/T 3880
PVC fim available
This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys
Alloy and temper designations are in accordance with ANSI H35.1.
Equivalent standard in Chinese: GB/T3190 for chemical composition and GB/T3880 for mechanism properties.
General Quality:
Unless otherwise specified, the material shall be supplied in the mill finish and shall be uniform as defined by the requirements of this specification and shall be commercially sound. Any requirement not covered is subject to negotiation between producer and purchaser.
Each sheet and plate shall be examined to determine conformance to this specification with respect to general quality and identification marking. On approval of the purchaser, however, the producer may use a system of statistical quality control for such examinations.
|
Alloy |
Temper |
Thickness(mm) |
|
1235 |
H12, H22 |
> 0.20-4.50 |
|
H14, H24 |
> 0.20-3.00 |
|
|
H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
1070 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H14, H24 |
> 0.20-6.00 |
|
|
H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
1060 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22 |
> 0.50-6.00 |
|
|
H14, H24 |
> 0.20-6.00 |
|
|
H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
1050, 1050A |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H14, H24 |
> 0.20-6.00 |
|
|
H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
1145 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H14, H24, H16, H26, H18 |
> 0.20-4.50 |
|
|
1100 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22 |
> 0.20-6.00 |
|
|
H14, H24, H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
1200 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H14, H24 |
> 0.20-6.00 |
|
|
H16, H26 |
> 0.20-4.00 |
|
|
H18 |
> 0.20-3.00 |
|
|
3003 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H14, H24 |
> 0.20-6.00 |
|
|
H16, H26, H18 |
> 0.20-4.00 |
|
|
H28 |
> 0.20-3.00 |
|
|
3004 3104 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H32, H14 |
> 0.20-3.00 |
|
|
H24, H34, H16, H26, H36, H18 |
> 0.20-1.50 |
|
|
H28, H38 |
> 0.20-3.00 |
|
|
3005 |
O, H111, H12, H22, H14 |
> 0.20-6.00 |
|
H16 |
> 0.20-4.00 |
|
|
H24, H26, H18, H28 |
> 0.20-3.00 |
|
|
3105 |
O, H12, H22, H14, H24, H16, H18 |
> 0.20-3.00 |
|
H28 |
> 0.20-1.50 |
|
|
3102 |
H18 |
> 0.20-3.00 |
|
5182 |
O |
> 0.20-3.00 |
|
H19 |
> 0.20-1.50 |
|
|
5A03 |
O, H14, H24, H34 |
> 0.50-4.50 |
|
5A05, 5A06 |
O |
> 0.50-4.50 |
|
5082 |
H18, H38, H19, H39 |
> 0.20-0.50 |
|
5005 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H32, H14, H24, H34 |
> 0.20-6.00 |
|
|
H16, H26, H36 |
> 0.20-4.00 |
|
|
H18, H28, H38 |
> 0.20-3.00 |
|
|
5052 |
F |
> 2.50-8.00 |
|
O |
> 0.20-6.00 |
|
|
H12, H22, H32, H14, H24, H34 |
> 0.20-6.00 |
|
|
H16, H26, H36 |
> 0.20-4.00 |
|
|
H18, H38 |
> 0.20-3.00 |
|
|
5083 |
O |
> 0.50-4.00 |
|
H22, H32 |
> 0.50-4.00 |
|
|
8006, 8011, 8011A |
O |
> 0.20-3.00 |
|
H14, H24, H18 |
> 0.20-3.00 |
